Pacific C360 DDC Soft Tube Water Cooling Kit Pacific C360 DDC Soft Tube Water Cooling Kit Pacific C360 DDC Soft Tube Water Cooling Kit Pacific C360 DDC Soft Tube Water Cooling Kit Pacific C360 DDC Soft Tube Water Cooling Kit Pacific C360 DDC Soft Tube Water Cooling Kit Pacific C360 DDC Soft Tube Water Cooling Kit
Pacific C360 DDC Soft Tube Water Cooling Kit

Pacific C360 DDC Soft Tube Water Cooling Kit

In stock
P/N
CL-W253-CU12SW-A
AUD$599.00

LCS Combo kit with Pump/Reservoir, T1000 coolant, fittings, copper radiator, soft tubes and 5V motherboard software controllable 120mm fans and W4 ARGB water block and other accessories.

Cautions

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks

  • To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  • Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  • Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup

  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
  • Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
  • DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
  • Fill the reservoir to the top as it will prevent air from going into the pump
  • If necessary tilt the system slightly from side to side to bleed the air out of the loop.
  • Place some paper towels under fittings and joining points to test for leaks.
  • Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
  • Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
  • Coolant might fade over time.
More Information
P/N CL-W253-CU12SW-A
Dimensions 520 (L) x 200 (W) x 232 (H)
Compatibility Intel LGA 2066/2011/1700/1366/1156/1155/1151/1150
AMD AM5/AM4/FM2/FM1/AM3+/AM3/AM2+/AM2
Components Dimension Pump & Reservoir: 86.54 (L) x 62 (W) x 140.1 (H) mm
Copper Radiator : 29.5 (H) x 119 (W) x 399 (L) mm
Tube Dimension V-tubler 4T 1/2'‘(12.7mm) ID x 3/4'‘(19mm) OD Transparent Tube x2 Meters
Fan Spec PWM 500~1500 RPM ,
( ARGB Controller or 5V MB ARGB Sync )
Coolant T1000 Coolant Pure Clear
Kit Contents CPU Water Block
- Pacific W4 ARGB CPU Water Block x1

Pump/Reservoir
- Pacific PR15-DDC Pump/Reservoir Combo x1

Copper Radiator
- Pacific C360 Radiator 29.5 (H) x 119 (W) x 399 (L) mm x1

ARGB Fan
- Pure 12 ARGB Sync Radiator Fan TT Premium Edition x3
- ARGB LED Controller

Fittings
- Pacific 1/2'' ID x 3/4'' OD Compression - Black x6
- Pacific G1/4 90 Degree Adapter - Black x2

Coolant
- Thermaltake T1000 Coolant Pure Clear x1

Tube
- V-tubler 4T 1/2'‘(12.7mm) ID x 3/4'‘(19mm) OD
Transparent Tube x2 Meters

Accessory
- Intel and AMD Universal Backplated & Mounting Kit
- 24pin ATX Bridge Tool x1
- Thermaltake Thermal Grease x1